![]() |
| 15" wheels all around, but the stance is too high in the front |
HOME NEW: Visit my Mustang's Spec Page
Saturday, July 15, 2017
Fixing the Stance
Since I had rebuild the rear suspension with a mid-leaf spring kit, the front of the car has sat higher than the rear. I also upgraded the rear to 15" wheels, but due to how much it costs, I couldn't do the front wheels at the same time. Finally, this spring I was able to get the front wheels and also ended up cutting the front springs to address the stance of the car. I went with P225/60R15 tires for the front.
Rebuilding Rear Ends
This one is going to go back in time as I started this project back in February 2016. The goal was to finish the back suspension of the car and add an Eaton TrueTrac to the rear differential. So the plan was for me to rebuild the rear end and put everything back together with a new suspension. I also decided to upgrade the rear brakes from drums to discs.
![]() |
| Out with the old suspension and rear axle |
Sunday, February 22, 2015
Double Pumping
Carburetors. Archaic technology (hasn't been sold on a car since 1990) and very temperamental (hard to dial in). I only say this because I have been having a hell of a time getting them to work for me. I inherited with my car a Holley 4160 600 CFM which comes with vacuum secondaries. This means the carb relies on the vacuum created at higher rpms to pull the fuel into the secondary fuel bowl (higher rpms require more fuel to be fed into the engine to meet the demand). It is actually a pretty nice bit of engineering (for the time), and in theory the fuel is delivered when it is needed. This was not the case for my 4160. I am not sure if it was due to the lower vacuum my engine pulls because of the bigger cam, or what, but I could never get the secondaries to open on my carb. I tried lighter springs and a new diaphragm, but I could never get it to work correctly. It was costing me horsepower. And then one fateful day, the whole carb decided to die in spectacular fashion. Gas just started spewing everywhere from every seal. I had enough.
![]() |
| The old 4160 |
Saturday, May 24, 2014
Spring Projects Completed
Last time we left off I was describing how what started out as a simple project has grown into a monster project. Long story short, I was going to pull the engine and trans in order to freshen things up and replace things like a new radiator, clutch, flywheel, shift kit, and the infamous rear main oil seal that I have been trying to avoid since I've had the car.
Here's a rundown of each of the projects:
Rear Main Oil Seal and Engine
Once I got the engine out of the car, I had to break down the engine from the flywheel back. Once I removed all those parts, I could put the engine on the engine stand. Except there was one problem. The new engine puller has legs that come out in the shape of a 'V' and the engine stand has boxed legs. Have you ever put a square peg into a round hole? Doesn't work. So I had to go out and get a new engine stand. The good news is I have an engine stand for sale. Anyone interested?
Once I was able to finally get the engine on the stand I went to work on the rear main oil seal. For the rear main oil seal I went with a Fel-Pro Fluoroelastomer gasket from JEGS. Except, when I ordered it I got an email saying it was out of stock and on back order and they requested the vendor send it directly to me. After some research I found out that it was out of stock everywhere! I was scrambling everywhere trying to find this part. I even called Fel-Pro and they said they were waiting on production and it could take up to six months. Right when I was ready to cancel my order with JEGS, a package showed up at my door and it was the rear main oil seal gasket!
I also picked up some Corporate Ford Blue engine paint, new freeze plugs, intake and exhaust gaskets. I was also able to check the oil pickup depth since I had the engine out (something I didn't do when I installed it). I never had any problems with it, but I just needed the peace of mind knowing that it is now 1/2" above the bottom of the pan.
![]() |
| Coming out party |
Rear Main Oil Seal and Engine
![]() |
| Whelp, this isn't going to work |
Once I was able to finally get the engine on the stand I went to work on the rear main oil seal. For the rear main oil seal I went with a Fel-Pro Fluoroelastomer gasket from JEGS. Except, when I ordered it I got an email saying it was out of stock and on back order and they requested the vendor send it directly to me. After some research I found out that it was out of stock everywhere! I was scrambling everywhere trying to find this part. I even called Fel-Pro and they said they were waiting on production and it could take up to six months. Right when I was ready to cancel my order with JEGS, a package showed up at my door and it was the rear main oil seal gasket!
I also picked up some Corporate Ford Blue engine paint, new freeze plugs, intake and exhaust gaskets. I was also able to check the oil pickup depth since I had the engine out (something I didn't do when I installed it). I never had any problems with it, but I just needed the peace of mind knowing that it is now 1/2" above the bottom of the pan.
Subscribe to:
Posts (Atom)




